PowerBox Work With ECU Programmer Power Box For Openport 2.0 J2534 Car Transmission Device Box

15 000 دج

الفئات: Outils de diagnostics
المنطقة: ورقلة
وضع في: 24-08-2023 à 16:19:34

الوصف

PowerBox Work With ECU Programmer Power Box For Openport 2.0 J2534 Car Transmission Device Box Power Upgrade Tool Best Price

Description:

It is compatible in automatic mode with loading programs that use:

BOOT-OEM12, 12 pin OBD-II;

L-LINE, 15 pin OBD-II.

The tool has built-in current limiting resistors on the following signal lines:

RESET - 510Ω;

Start-510 Ω;

CNF1 - 220Ω.

In summary:

All above programming tools can be used for ECU reading and writing, but differs in ECU coverage and read/write method.

There is no limit of car model and year when using the bench to read/write data.

But if you have chips and gearboxes to read and write, you should have flash. The bad is: disassembly is required. The bench does not cover chips and gearboxes and OBD can't work well for gerabox read/write.

So you'd better check the ECU/Gearbox/Chip before your purchase.

Check the list of each car on the corresponding product page.

The tool is equipped with versatile connectors that allow connections to be made flexibly:

USB:

Designed to connect to computer. It must be connected when the built-in usb-uart converter is enabled; For PowerBox software update; While reprogramming Renesas processors;

CD:

Designed to power the integrated circuit as well as the connected ECU. It is recommended to use only quality units with an output voltage of 12V. Reading the password, when it is impossible in the vehicle, it should be noted that the high voltage converters in the ECUs consume rather high current at the beginning, which may trigger the protection mechanism or even damage the power unit ;

J2534 (OBD-II-F):

Designed to connect the interface of the same name to OBD-II;

DB-15:

Designed to connect to the main ECU connector. It is recommended to use 14P600KT02, 14P600KT03 cables or analog cables;

IDC-26:

Designed to connect directly to the ECU board or via the special head adapter. It is recommended to use a 14P600KT06 cable or an analog cable for Tricore GPT.

It is recommended to use Flash Developer Toolkit software for flashing Renesas processors.

Controls:

The tool has 3 switches to operate in different modes.

Powerful:

Power control. The tool has three ECU power modes: OFF removes all power and control signals from IDC-26 and DB-15 connectors; the manual supply of the VECU and VKEY terminals and the control outputs according to the chosen tactic; Automatic control, automatic, In this mode, the power supply is controlled by the loading program with an L line signal (15 pin OBD-II).

Boot:

Simultaneous control of start, reset and CNF1 (3.3V) signals: disabled, allows all control signals to be removed from the DB-15 connector; Manually pull reset and start to minus signal, and CNF1 to +3.3V; Automatic control, in this boot mode, RESET and CNF1 signals are simultaneously controlled by the loader program (12 pin OBD-II, OEM12).

GPT:

Dor for Renesas and for Tricore with GPT cpu. It is necessary to use 5V while working with SH705x processors, in other cases 3.3V should be used.

Lights:

The LED next to the 5V/3.3V switch indicates a voltage supply of 5V or 3.3V.

VECU, VKEY LED indicates VECU and VKEY power supply voltage.

The 12V LED indicates the supply voltage.

The start LED indicates the voltage on the CNF1 output (the LED works for both input and output).

Package List:

1 x PowerBox for Flash

1 x color wire chart

1 x GPT color cable

1 x charger plug

المعلن الخاص